NSE5_FAZ-6.2 Fortinet NSE 5 - FortiAnalyzer 6.2 exams demo

QUESTION 1
Which two of the following must you configure on FortiAnalyzer to email a FortiAnalyzer report externally?
(Choose two.)
A. Mail server
B. Output profile
C. SFTP server
D. Report scheduling
Correct Answer: BC
Section: (none)
Explanation
Explanation/Reference:
Reference: https://fortinetweb.s3.amazonaws.com/docs.fortinet.com/v2/attachments/6d9f8fb5-6cf4-11e9-81a4-
00505692583a/FortiAnalyzer-6.0.5-Administration-Guide.pdf (119)

,

,

QUESTION 3
For which two purposes would you use the command set log checksum? (Choose two.)
A. To help protect against man-in-the-middle attacks during log upload from FortiAnalyzer to an SFTP server
B. To prevent log modification or tampering
C. To encrypt log communications
D. To send an identical set of logs to a second logging server
96CE4376707A97CE80D4B1916F054522
Correct Answer: AB
Section: (none)
Explanation
Explanation/Reference:
Explanation:
To prevent the log in the store from being modified, you can add a log checksum by using the config system
global command. When the log is split, archived, and the log is uploaded (if the feature is enabled), you can
configure the FortiAnalyzer to log the log file hash value, timestamp, and authentication code. This can help
defend against man-in-the-middle attacks when uploading log transmission data from the FortiAnalyzer to the
SFTP server.
.

.

.

.
QUESTION 5
You are using RAID with a FortiAnalyzer that supports software RAID, and one of the hard disks on
FortiAnalyzer has failed.
What is the recommended method to replace the disk?
A. Shut down FortiAnalyzer and then replace the disk
B. Downgrade your RAID level, replace the disk, and then upgrade your RAID level
C. Clear all RAID alarms and replace the disk while FortiAnalyzer is still running
96CE4376707A97CE80D4B1916F054522
D. Perform a hot swap
Correct Answer: D
Section: (none)
Explanation
Explanation/Reference:
Reference: https://www.fortinetguru.com/2016/04/system-settings/6/
QUESTION 6
On the RAID management page, the disk status is listed as Initializing.
What does the status Initializing indicate about what the FortiAnalyzer is currently doing?
A. FortiAnalyzer is ensuring that the parity data of a redundant drive is valid
B. FortiAnalyzer is writing data to a newly added hard drive to restore it to an optimal state
C. FortiAnalyzer is writing to all of its hard drives to make the array fault tolerant
D. FortiAnalyzer is functioning normally
Correct Answer: C
Section: (none)
Explanation
Explanation/Reference:
Reference: https://fortinetweb.s3.amazonaws.com/docs.fortinet.com/v2/attachments/4cb0dce6-dbef-11e9-
8977-00505692583a/FortiAnalyzer-5.6.10-Administration-Guide.pdf (40)
QUESTION 7
In the FortiAnalyzer FortiView, source and destination IP addresses from FortiGate devices are not resolving to
a hostname.
How can you resolve the source and destination IP addresses, without introducing any additional performance
impact to FortiAnalyzer?
A. Resolve IP addresses on a per-ADOM basis to reduce delay on FortiView while IPs resolve
B. Configure # set resolve-ip enable in the system FortiView settings
C. Configure local DNS servers on FortiAnalyzer
D. Resolve IP addresses on FortiGate
Correct Answer: B
Section: (none)
Explanation
Explanation/Reference:
Reference: https://forum.fortinet.com/tm.aspx?m=156950
QUESTION 8
You have recently grouped multiple FortiGate devices into a single ADOM. System Settings > Storage Info
shows the quota used.
What does the disk quota refer to?
A. The maximum disk utilization for each device in the ADOM
B. The maximum disk utilization for the FortiAnalyzer model
C. The maximum disk utilization for the ADOM type
D. The maximum disk utilization for all devices in the ADOM
96CE4376707A97CE80D4B1916F054522
Correct Answer: B
Section: (none)
Explanation
Explanation/Reference:
QUESTION 9
Why should you use an NTP server on FortiAnalyzer and all registered devices that log into FortiAnalyzer?
A. To properly correlate logs
B. To use real-time forwarding
C. To resolve host names
D. To improve DNS response times
Correct Answer: A
Section: (none)
Explanation
Explanation/Reference:
QUESTION 10
You need to upgrade your FortiAnalyzer firmware.
What happens to the logs being sent to FortiAnalyzer from FortiGate during the time FortiAnalyzer is
temporarily unavailable?
A. FortiAnalyzer uses log fetching to retrieve the logs when back online
B. FortiGate uses the miglogd process to cache the logs
C. The logfiled process stores logs in offline mode
D. Logs are dropped
Correct Answer: B
Section: (none)
Explanation
Explanation/Reference:
QUESTION 11
After you have moved a registered logging device out of one ADOM and into a new ADOM, what is the purpose
of running the following CLI command?
execute sql-local rebuild-adom <new-ADOM-name>
A. To reset the disk quota enforcement to default
B. To remove the analytics logs of the device from the old database
C. To migrate the archive logs to the new ADOM
D. To populate the new ADOM with analytical logs for the moved device, so you can run reports
Correct Answer: B
Section: (none)
Explanation

Buy full version for more questions